Roof Leak Repair
Submitted by
staff on Wed, 03/10/2010 at 5:34am.
(By Suketu Mehta)
Roof leaks are highly irritating as you would not like water continuously dripping inside your home. There are various causes for a roof leak. It could be due to cracks or gaps formed on the shingles, a cracked part on a flat roof or even blisters or gaps formed along the chimney, vent or flashing. It is not always necessary to replace the whole roofing in case of a leak. You can easily perform a roof leak repair job yourself, following instructions listed below, and solve your problem.
Roof Leak Repair : Materials Required
- Hammer
- Nails
- Pieces of dry cloth
- Metal bristled brush
- Trowel
- Roofing cement
- Roof patching fabric
- Knife
How to Fix a Leaky Roof
Locating the Leak
Step 1
Before you start your roof leak repair job which is an integral part of home improvement, it is important to locate exactly where the roof is leaking from. For this, move around your house and keenly observe the roof to find any hint of cracks or tears. More often than not, these are the places where the roof leaks from. Once you have located the source, mark these spots.
Step 2
After checking your roof from the inside your house, you need to inspect it from the outside. Go up to the roof and stroll around (wear flat shoes) to have a closer look at any weak spots up there. In case you find any, mark those spots. Also, carefully look over chimneys, vents and flashing for any cracks or worn out cement pieces.
Step 3
Go to your attic and use a flashlight to locate any water stains. You can easily get the leak source if you go after the water trail to the roof. If you find the source, just hammer a nail in there to make it easier to locate it when you go on the roof.
Roof Leak Repair
Step 1
Start with the various roofing attributes like vent, chimney or flashings. Remove whichever of these has any cracks or gaps by unscrewing them. Take out any cement or tar applied there previously. Scrape off all dirt and dust with a brush, and use a dry piece of cloth to soak up any water collected there. Now replace the old attribute with a new one. Fill any gaps or cracks with roofing cement using a trowel. To prevent any further water leakage and facilitate draining of water, fill extra cement in cracks and gaps.
Step 2
Remove roofing shingles from the roof which are causing the leak, by gently peeling them off their edges. At the source of leakage, apply roofing cement and fill the gap. If you find any extra nails, take them out and replace with new ones. Apply some roofing cement over these nails as well. Read more on how to clean roof shingles.
Step 3
You will then need to fill any rubber sheathing cracks with roofing cement. Ensure you apply a couple of extra patches of cement on the cracks, to reduce chances of leakage in future. Implant a roof patching fabric with the cement and give one last coat on the cracks.
Step 4
You will then need to fix any bubbles, wrapping or blisters formed in the roof sheathing. Carefully remove the flaps along the troubled area. Under these flaps, apply roofing cement. Put back the flaps you removed. Cover these flaps with another layer of cement, and in the process try and flatten them out as much as possible. Now, alternately apply two layers each of cement and patching fabric over the troubled spot, and you are done.
In case you want to get the roof leak repair job done from outside, the roof leak repair cost would come to anywhere between US $150 to US $800, depending on the type of roof, the amount of work required and also whom you approach for this work.
Read more on:
While performing the roof leak repair task, you should be careful whenever you are working on top of the roof. Use safety ropes, wear flat rubber sole shoes and do the job on a sunny day when the roof surface is dry.
(Article Source:http://www.buzzle.com)
|
22 reads | 0 comments |
0 votes: